Wire line trolling tips & tricks
This seems to be a hot topic lately so I thought I would start a new thread where we can share some tips, tricks and ideas that we do when trolling with wire line. Below are some of the things we do, I know a lot is personal preference. Please post your methods and ways in comments so others can also learn and pickup new ways of doing some old things. Enjoy.
Wire Types: Basically there are two types used, monel and stainless. Monel is denser than stainless but much more forgiving, it is less springy than stainless and does not kink as much. But that comes at a cost of about three times the price for the same test line and 300′ length. Monel also stretches over time causing it to get thinner and thinner. Depending on how much you troll the wire will determine how long it takes for it to get thin enough to cause mystery break offs. I typically use a shot of wire for two to three seasons or, four to six half seasons depending on if you started using the shot in the spring or fall.
Marking Wire: I have tried the Malin pre-marked wire and it is not worth the extra money or even for the same money as non-marked. They started to slide on the wire the very first day we used them. I know a few shop owners that fought with Malin to give them refunds on the large spools they fill reels from because they had issues with them sliding as well. The best method I have come across is not easy to do and I have not mastered it yet…basically you use colored phone wire and create haywire twists and barrel wraps with the telephone wire onto the monel or stainless. When done this way they will never move for the life of the wire since they are interlocked with the haywire twist. The second best method I have used is to take a small board and pound two nails through it about a foot apart. Then cut a rubber band and tie each end around a nail stretching it a good amount in the process. Lay the wire over the stretched rubber band and then wrap tightly a colored piece of wire ten to fifteen times finishing with seven to nine barrel wraps on each end. This creates a good visual and also feeling mark if fishing in low light conditions. You can mark your wire however often as needed for your fishing habits. I personally mark it at 150′, 200′ and 250′ as this covers all our needs.
Trolling Habits: I usually troll deeper water so we usually have the hole 300′ out but if you are inshore and not deploying the whole shot of wire you should let out a few feet or crank in a few feet every ten to fifteen minutes to avoid creating a kink and also wearing a weak spot into monel especially, but should also do this with stainless.
Aluminum Spools: I have had Shimano Tekota 800 reels for three seasons now and my spools are healthy and fine. Yes they have a few pits on them but I have also seen worse on older Penn Senators with steel spools. The new anodized aluminum spools hold very well with wire line as long as you take care of them. We wash our rods and reels down after each trip, towel or chamois them off and then liberally apply CRC 656 to the whole reel and the wire, let it soak in a bit then towel off the reel and leave the wire coated well. This extends the life of the wire and the spool. Also about once a month or if I suspect damage I lay the rod on my bench, attach a hand crank spool to the other end and remove the wire from the reel looking for damage to the wire and also checking the marks are in the right location with a line counter. I also take this time to clean the exposed portion of the spool and apply some CRC directly to it. Once I am satisfied the line is OK I crank it back onto the reel pulling it through an oil soaked rag.
Wire to Mono Knots: To attach the wire to the backing I tie a Bimini twist in the backing first. Then I tie a long slender haywire twist in both ends of the wire line. This allows you to use a loop-to-loop connection to your backing and replace a shot of wire quickly and easily on the water should you break off, kink or have other damage to your wire causing it to be unusable. For the leader I tie a twelve to fifteen turn Albright knot and use eight to twelve feet of eighty or one hundred pound fluorocarbon leader to which I attach a two hundred pound ball bearing snap swivel.
Spoon Attachment Points: Whether the spoon comes with one or not I always attach a heavy duty, stainless split ring to it. I have had several spoons fail or severely weaken by them being attached directly to the snap swivel.
Spoon Weights: On spoons with weights I use either 3M marine silicone sealant or 5200 (whichever is handy). Most manufacturers of spoons recommend that you check the screws every fifteen minutes of use. I have found that if you bed them well with the silicone sealant or 5200 you pretty much don’t ever have to worry about them coming loose and losing a weight to the screws loosening from the pumping action.
Trolling Speed: This has a lot of personal preference but we usually don’t look at our tach or our SOG or SOW readings as much as we watch the rod tips. One thing we try to avoid at all costs though is trolling with the current. We always troll against it or across it. As for the actual speed we adjust the throttle till we have big slow pulses in the rods. You can run the spoon only a few feet behind the boat so you can see if it is wobbling back and forth or spinning. This will give you an idea of what the pulsing of the rod tip should look like.
Spare Shots of Wire: You have extra rods, reels, plugs, plastics, sinkers and everything else you use…carry an extra shot of wire. I keep at least one sometimes two spare shots with the trolling gear. You can mark them ahead of time and tie the haywire twists in the ends and even attach the flouro leader too. If you use a Bimini twist in your backing changing it out is a breeze as long as the damage to the line or where it parted is not in your backing. Even if it was once proficient with a Bimini it only takes a minute or two to whip another into your backing. Having a spare or two on board can really save the day sometimes.
Hey, nice tips. Perhaps I’ll buy a glass of beer to that man from that forum who told me to visit your site
Thanks, I will be updating many sections as the season rolls along with how to pics and videos. Which forum did you get the referral from?